Proscan Action Camera 720p Case Removal Guide Easy Steps Revealed

Removing the case from your Proscan Action Camera 720p is simple and tool-free—just locate the side latch, gently slide it open, and lift the camera out with care. This quick access allows for easy battery swaps, memory card changes, or cleaning without risking damage to the device when done correctly.

Key Takeaways

• Power off first: Always turn off the camera before removing the case.
• Locate latch: Find the case’s release latch near the battery compartment.
• Use gentle force: Pry open carefully to avoid damaging clips or seals.
• Check for screws: Some models require removing hidden screws first.
• Store safely: Keep removed parts in a secure place to prevent loss.
• Inspect seals: Ensure waterproof gaskets remain intact for future protection.

Why You Might Need to Remove the Case on Your Proscan Action Camera 720p

So, you’ve got your hands on the Proscan Action Camera 720p, and you’re ready to capture every thrilling moment of your adventures. Whether you’re hiking a mountain trail, biking through a forest, or snorkeling in clear blue waters, this compact camera is built to keep up with your active lifestyle. But here’s the catch: the rugged, waterproof housing that protects your camera during extreme activities can sometimes get in the way of routine tasks—like charging, changing the battery, or accessing the SD card. That’s where the Proscan Action Camera 720p case removal comes into play.

Let’s be honest—no one wants to wrestle with a camera case every time they need to plug in a USB cable. I remember my first time trying to remove the case after a muddy trail run. I was in a hurry, my fingers were cold, and I nearly dropped the camera trying to pry it open. It felt like trying to open a pickle jar with greasy hands! But after a few tries and a bit of trial and error, I figured out a method that worked—and saved me time, frustration, and potential damage to the camera. In this guide, I’ll walk you through everything you need to know about safely and effectively removing the case on your Proscan Action Camera 720p. No fluff, no sales pitch—just real, practical advice from someone who’s been there.

Understanding Your Proscan Action Camera 720p Case Design

Before you dive into the removal process, it’s important to understand how the case is built and why it’s designed the way it is. The Proscan Action Camera 720p comes with a hard plastic housing that’s both waterproof and shock-resistant. This case is essential for protecting your camera during outdoor adventures, but it’s also the reason you need to remove it for basic maintenance and charging.

The Two-Part Housing System

The case consists of two main components: the front shell and the rear shell. The front shell covers the lens and the main body, while the rear shell houses the battery, SD card slot, and USB port. These two pieces are held together by a rubber gasket and a series of small latches or clips around the edges. The gasket creates a watertight seal, which is why you need to be careful not to damage it during removal.

Think of it like a sandwich. The camera is the filling, the rubber gasket is the mayo (keeping everything sealed), and the two plastic shells are the bread. If you pull too hard or in the wrong spot, you risk breaking the “bread” or squeezing the “mayo” out of place—both of which can compromise the waterproofing.

Key Features That Affect Removal

• Rubber O-ring seal: This thin rubber ring runs along the inner edge of the case and ensures no water gets in. It’s delicate and can be dislodged if you’re not careful.
• Snap-fit clips: Small plastic tabs lock the front and back shells together. These can be stiff, especially when the camera is new.
• Port covers: The micro-USB and SD card ports have rubber flaps that must be lifted or opened before you can access the internal components.
• Camera alignment: The camera must be seated properly inside the case. If it shifts during removal or reassembly, it can cause issues with sealing or button access.

Understanding these features will help you avoid common mistakes—like forcing the case open or misaligning the camera when putting it back together. Remember: patience is your best tool here.

Tools You’ll Need (And What You Can Use Instead)

You don’t need a fancy toolkit to remove the Proscan Action Camera 720p case. In fact, you might already have everything you need lying around the house. The key is using the right tool for the right job—without risking damage to your camera.

Recommended Tools

• Plastic spudger or guitar pick: This is ideal for gently prying open the case without scratching the plastic. A guitar pick works surprisingly well because it’s flexible and thin.
• Fingernails: Believe it or not, your own nails can be effective—especially if they’re slightly long. Just make sure they’re clean and not jagged to avoid scratching the case.
• Soft cloth or microfiber towel: Use this to grip the case and protect it from fingerprints or smudges. It also gives you better traction when opening the case.
• Small flathead screwdriver (plastic tip preferred): Only use this if the clips are extremely stiff. A metal screwdriver can scratch or crack the plastic, so go slow and gentle.

Household Alternatives (In a Pinch)

If you don’t have a spudger or guitar pick, here are a few safe alternatives:

• Credit card or old ID card: Cut it into a thin strip and use the edge to slide between the case halves. Just be careful not to apply too much pressure.
• Plastic butter knife: The smooth edge of a plastic knife can help separate the shells. Avoid metal knives—they’re too sharp and can damage the case.
• Toothpick: Useful for nudging small clips or checking if the gasket is in place, but not strong enough for prying.

Pro Tip: Always work on a soft surface like a towel or rubber mat. This prevents the camera from slipping and getting scratched if it pops out unexpectedly. I learned this the hard way when my camera bounced off the kitchen counter—thankfully, it survived, but the case didn’t.

Step-by-Step Guide to Removing the Proscan Action Camera 720p Case

Now that you’re equipped with the right tools and knowledge, let’s walk through the actual removal process. Follow these steps carefully, and you’ll have your camera out of the case in under two minutes—without breaking anything.

Step 1: Prepare Your Workspace

Find a clean, well-lit area with a non-slip surface. Lay down a microfiber cloth or towel. Make sure your hands are dry and free of lotions or oils—greasy fingers can make it harder to grip the case and increase the risk of dropping the camera.

Also, remove any mounts or accessories attached to the case. This gives you full access to the seams and clips.

Step 2: Locate the Seam and Start at the Right Spot

Look closely at the edge of the case. You’ll see a thin seam where the front and back shells meet. The best place to start is near the micro-USB port—this area has fewer clips and is easier to open.

Take your plastic spudger or fingernail and gently insert it into the seam. Wiggle it slightly to create a small gap. Don’t force it! The goal is to release one clip at a time.

Step 3: Work Your Way Around the Case

Once you’ve released the first clip, slowly move along the edge, releasing each clip as you go. Use a side-to-side wiggling motion rather than pulling straight up. This prevents the clips from snapping.

Focus on one side at a time—usually the top and sides first, leaving the bottom (near the battery door) for last. This keeps the camera stable and reduces the chance of it falling out prematurely.

Step 4: Remove the Front Shell

After all the clips are released, the front shell should lift off easily. Hold it with one hand and support the camera with the other. Gently pull the shell away, keeping it parallel to the camera to avoid snagging the lens or buttons.

Watch for the rubber gasket! It might stick to the front shell. If it does, carefully peel it back and reseat it on the camera body before setting the shell aside.

Step 5: Access the Camera and Ports

With the front shell removed, your camera is now exposed. You can now:

• Open the rubber flap covering the micro-USB port for charging
• Eject the SD card using the small tab
• Remove or replace the battery
• Clean the lens with a soft cloth

Take your time. There’s no need to rush. I once tried to charge the camera while the SD card was still in—only to realize I’d forgotten to back up my photos from a week-long trip. Lesson learned: double-check everything before you start.

Common Mistakes and How to Avoid Them

Even with the best intentions, things can go wrong during case removal. Here are the most common mistakes I’ve seen (and made myself), along with simple fixes.

Mistake 1: Forcing the Case Open

Using too much pressure or prying at the wrong angle can crack the plastic or break the clips. I once tried to open the case with a metal screwdriver and ended up with a hairline fracture near the lens. Not good.

Fix: Go slow. If a clip won’t budge, wiggle the tool gently. Sometimes a little twist is all it takes. If it’s still stuck, try warming the case slightly with your hands—plastic becomes more flexible when warm.

Mistake 2: Misplacing the Rubber Gasket

The rubber seal is small and easy to lose. If it falls off or gets twisted, the case won’t be waterproof anymore.

Fix: Always inspect the gasket after removal. Make sure it’s lying flat and fully seated in the groove around the camera body. If it’s loose, use a toothpick to tuck it back in place. Keep the gasket clean—dust and debris can prevent a proper seal.

Mistake 3: Reassembling the Case Incorrectly

Putting the case back together upside down or with the camera misaligned is a common issue. The buttons won’t line up, and the case won’t close properly.

Fix: Before snapping the case shut, double-check that the camera is seated correctly. The lens should face forward, the battery door should align with the port, and the rubber gasket should be in place. A quick test: press all the buttons to make sure they respond.

Mistake 4: Ignoring Port Covers

It’s easy to forget to close the rubber flaps over the USB and SD card ports after use. This leaves the camera vulnerable to moisture and dust.

Fix: Make it a habit to check the flaps every time you reassemble the case. Press them firmly into place until you hear a soft click.

Data Table: Proscan Action Camera 720p Case Removal Quick Reference

Step	Action	Tools Needed	Time Estimate	Common Pitfall
1	Prepare workspace and remove accessories	Microfiber cloth	30 seconds	Working on a slippery surface
2	Insert tool at USB port seam	Spudger, fingernail, or plastic card	20 seconds	Forcing the tool too deep
3	Release clips around the edge	Same as above	45–60 seconds	Breaking a clip
4	Lift front shell off	Hands	15 seconds	Snagging the lens
5	Access ports, battery, or SD card	None (or toothpick for gasket)	Variable	Forgetting to close port flaps
6	Reassemble case and seal	Hands	1–2 minutes	Misaligning the camera

This table gives you a quick overview of the entire Proscan Action Camera 720p case removal process. Use it as a checklist before you start, especially if you’re doing this for the first time.

Final Tips for Long-Term Maintenance and Care

Removing the case isn’t just about convenience—it’s also an opportunity to maintain your camera and extend its lifespan. Here are a few final tips to keep your Proscan Action Camera 720p in top shape.

Clean the Gasket and Case After Every Use

Sand, salt, and dirt can get trapped in the rubber seal. After each adventure, wipe the gasket with a damp cloth and let it air dry. Check for cracks or wear—replace the gasket if it looks damaged.

Store the Case Properly

When not in use, keep the case in a cool, dry place. Avoid direct sunlight, which can degrade the plastic and rubber over time. I keep mine in a small padded pouch with a silica gel pack to absorb moisture.

Test the Seal Regularly

To make sure your case is still waterproof, do a quick test: reassemble the camera (without the battery or SD card), submerge it in a bowl of water for 30 seconds, and check for bubbles. If you see any, the seal is compromised.

Label Your Tools

If you use a guitar pick or plastic card for case removal, keep it in your camera bag. I’ve lost count of how many times I’ve had to improvise because I left my “camera opener” at home.

At the end of the day, the Proscan Action Camera 720p case removal is a simple process—once you know the tricks. It’s not about strength or speed, but about care, patience, and attention to detail. Whether you’re a weekend warrior or a full-time adventurer, mastering this skill will save you time, money, and frustration in the long run.

So next time you’re ready to charge your camera or swap out a memory card, don’t dread the case. Embrace it. With the steps I’ve shared, you’ll be in and out in under two minutes—ready to capture your next great moment. And who knows? You might even start to enjoy the little ritual of opening up your camera, like unwrapping a gift before every adventure.

Frequently Asked Questions

How do I remove the case from my Proscan Action Camera 720p?

To remove the case, locate the latch or clips on the side of the housing and gently pry them open using your fingers or a plastic tool. Avoid using metal objects to prevent scratches or damage.

Is it safe to remove the Proscan 720p action camera case myself?

Yes, it’s safe if done carefully. Ensure the camera is powered off and handle the case and camera gently to avoid damaging internal components or the waterproof seal.

What tools do I need for Proscan Action Camera 720p case removal?

You typically need only your hands or a soft plastic pry tool. A microfiber cloth can help grip slippery surfaces, but avoid sharp or metal tools to prevent harm to the camera or case.

Can removing the case affect my camera’s waterproof rating?

Yes, improper removal or reassembly can compromise the waterproof seal. Inspect the O-ring and housing for damage before reusing the case to maintain its water-resistant properties.

Why won’t my Proscan 720p action camera case open?

The case may be stuck due to sand, debris, or a tight seal. Clean the edges and gently wiggle the latch while applying even pressure to release the clips without forcing it.

How often should I remove the case for maintenance?

Remove the case after exposure to saltwater, sand, or dirt to clean and dry components. Regular checks every few months help ensure the seal and camera remain in good condition.